Oil leak frustration

Maintenance, repair, troubleshooting, etc.
User avatar
andrewed1
One of the Regulars
One of the Regulars
Posts: 237
Joined: Mon Oct 05, 2015 3:51 pm
Region:: Sydney, Australia
Motorcycles:: XJ600 Seca II - 1992 & a 2nd 92 xj600s
Location: Sydney, Australia
Australia

Sun Dec 24, 2017 2:13 am

Also,,, notice that when you changed the oil sump/pan gasket when you cleaned the old gasket off did you also clean it from the Block?? sometime the gaskets also sticks to the block so you may have installed the new gasket over some of the old gasket on the block which would also create a leak.

if you note in your picture you cane see the oil building on the to half (block side) for the oil gasket..

AND YES...

your clutch cover gasket needs replacing also..
User avatar
XJR38
New to XJR
New to XJR
Posts: 9
Joined: Fri Nov 03, 2017 4:22 am
Region:: Rotterdam, The Netherlands
Motorcycles:: XJ600R "91 and "93
Turkey

Sun Dec 24, 2017 12:46 pm

@andrewed1

Yes, I've also cleaned the old gasket off the engine (used fine sandpaper and an old toothbrush).
Thanks for the reminder though! :D
User avatar
etch
Lookin' Around
Lookin' Around
Posts: 22
Joined: Fri Mar 31, 2017 4:51 pm
Region:: Suffolk, UK
Motorcycles:: 1999 Yamaha XJ600 Diversion
Location: Suffolk, UK

Wed Dec 27, 2017 11:20 am

I had to replace the oil filter adaptor seal on my bike (UK Diversion, '99) p/n 93210-87723: it is a 87mm ID 4mm CS round profie o-ring. Should be had for the price of a coffee, just double check that part number matches your model - there's some variation.
User avatar
zoli2750
Lookin' Around
Lookin' Around
Posts: 45
Joined: Sun Mar 02, 2014 1:57 pm
Region:: europe
Motorcycles:: xj600s

Wed Dec 27, 2017 1:17 pm

hi,
87mm is outer, middle, or inner diameter?
assume its outer

thanks
zoli
User avatar
XJR38
New to XJR
New to XJR
Posts: 9
Joined: Fri Nov 03, 2017 4:22 am
Region:: Rotterdam, The Netherlands
Motorcycles:: XJ600R "91 and "93
Turkey

Thu Dec 28, 2017 11:17 am

etch wrote:
Wed Dec 27, 2017 11:20 am
I had to replace the oil filter adaptor seal on my bike (UK Diversion, '99) p/n 93210-87723: it is a 87mm ID 4mm CS round profie o-ring. Should be had for the price of a coffee, just double check that part number matches your model - there's some variation.
Thanks! :D
zoli2750 wrote:
Wed Dec 27, 2017 1:17 pm
hi,
87mm is outer, middle, or inner diameter?
assume its outer

thanks
zoli
87mm (Inside Diameter) 4mm (Cross sectional)


I have replaced the clutch cover gasket. It was all dried up, felt like rubber and was really hard to get off. (Will upload pictures soon).

I think that I need to take the oil-pan off again. It seems like I might have moved the gasket a little bit while putting everything back together.
User avatar
zoli2750
Lookin' Around
Lookin' Around
Posts: 45
Joined: Sun Mar 02, 2014 1:57 pm
Region:: europe
Motorcycles:: xj600s

Thu Dec 28, 2017 2:14 pm

:)
thanks
Post Reply

Navigation:

  Search

  New Posts

  Unread Posts

  The Wall

  Gallery

  About Us